Forum: Model A (1928-31)
Yesterday, 10:34 PM
|
Replies: 8
Views: 560
Re: Installing cowl lights
Ford may not have used a grommet or washer, but I had make one out of PVC in order for my cowl lights to have any semblance of facing forward.
|
Forum: Model A (1928-31)
04-15-2024, 01:21 PM
|
Replies: 36
Views: 2,839
Re: Peep mirrors
I solved the "short mounting stud" delima by adding a 1" barrel nut from the hardware store into the mix.
|
Forum: Model A (1928-31)
04-15-2024, 01:11 PM
|
Replies: 27
Views: 1,924
Re: Recommended Turning Signal Switch
I bought my Signal Stat 900 from Sacramento Vintage Ford. It was wired specifically for a Model A. That was 12 years ago and it has worked without a problem.
|
Forum: Model A (1928-31)
04-02-2024, 04:41 PM
|
Replies: 23
Views: 1,357
|
Forum: Model A (1928-31)
04-01-2024, 09:29 PM
|
Replies: 10
Views: 645
|
Forum: Model A (1928-31)
03-30-2024, 01:54 PM
|
Replies: 15
Views: 1,358
|
Forum: Model A (1928-31)
03-29-2024, 07:27 PM
|
Replies: 19
Views: 1,592
|
Forum: Model A (1928-31)
03-28-2024, 02:40 AM
|
Replies: 28
Views: 1,930
|
Forum: Model A (1928-31)
03-25-2024, 01:18 PM
|
Replies: 36
Views: 2,839
Re: Peep mirrors
I have the hinge pin mirror arms on both sides of my CCPU. I have 6" convex mirrors again on both sides. Best combination ever. Arms came from Snyder's, mirrors from Amazon.
|
Forum: Model A (1928-31)
03-16-2024, 03:34 PM
|
Replies: 7
Views: 628
|
Forum: Model A (1928-31)
03-16-2024, 03:47 AM
|
Replies: 25
Views: 1,804
|
Forum: Model A (1928-31)
03-13-2024, 12:38 PM
|
Replies: 5
Views: 399
Re: Identify this front main crank seal
That is probably a Burtz (modern) seal. If you replace it with the rope seal that came with your gasket set, you will have to replace the top half as well.
|
Forum: Model A (1928-31)
03-09-2024, 08:41 PM
|
Replies: 41
Views: 3,205
|
Forum: Model A (1928-31)
03-09-2024, 08:26 PM
|
Replies: 16
Views: 821
|
Forum: Model A (1928-31)
02-28-2024, 06:24 PM
|
Replies: 4
Views: 417
|
Forum: Model A (1928-31)
02-26-2024, 10:32 PM
|
Replies: 16
Views: 935
|
Forum: Model A (1928-31)
02-26-2024, 10:19 PM
|
Replies: 6
Views: 604
|
Forum: Model A (1928-31)
02-24-2024, 05:59 PM
|
Replies: 18
Views: 1,232
|
Forum: Model A (1928-31)
02-24-2024, 05:56 PM
|
Replies: 12
Views: 851
|
Forum: Model A (1928-31)
02-19-2024, 02:08 AM
|
Replies: 10
Views: 1,454
Re: Engine rebuilder?
If you were thinking of H&H, I personally will not use them for anything -- based on the engine that was in my rig when I bought it.
|
Forum: Model A (1928-31)
02-19-2024, 12:01 AM
|
Replies: 16
Views: 1,489
Re: Motor stand adapter for Model A engine
Just a hint: On mine, I drilled and tapped a couple of holes in order to have a place to store the bolts I use to bolt the adapter to the engine, that way I don't have to turn my shop upside down...
|
Forum: Model A (1928-31)
02-16-2024, 02:29 PM
|
Replies: 3
Views: 624
|
Forum: Model A (1928-31)
02-15-2024, 03:24 AM
|
Replies: 19
Views: 897
|
Forum: Model A (1928-31)
01-31-2024, 04:30 PM
|
Replies: 9
Views: 790
|
Forum: Model A (1928-31)
01-31-2024, 12:45 PM
|
Replies: 13
Views: 1,022
Re: Best Electric Fuel Pump?
I was using the Carter fuel pump offered by the Model A vendors until it failed. I then went to O"Rileys and bought one off the shelf. It has outlasted the Carter and is still going strong.
|