Forum: Early V8 (1932-53)
05-10-2024, 12:42 PM
|
Replies: 12
Views: 434
Re: Puttin a key in the drivers door
A Blair brand hole saw will make a really nice cut. Measure your right make a good diagram pattern. Cut away. What I’m wondering is the right door hole flat are is there a raise edge for the tumbler...
|
Forum: Early V8 (1932-53)
05-06-2024, 08:18 PM
|
Replies: 11
Views: 484
|
Forum: Early V8 (1932-53)
04-30-2024, 12:46 PM
|
Replies: 10
Views: 378
|
Forum: Early V8
04-19-2024, 12:49 PM
|
Replies: 0
Views: 94
|
Forum: Early V8 (1932-53)
03-12-2024, 04:08 PM
|
Replies: 13
Views: 642
|
Forum: Early V8 (1932-53)
02-08-2024, 09:57 PM
|
Replies: 6
Views: 573
Re: 36 door window glass remove/replace
You won’t know thickness till you get your new glass. The setting tape comes in different thickness. You buy it at an upholstery supply. You can gently pinch the lower glass together if it’s a lot...
|
Forum: Early V8 (1932-53)
02-08-2024, 07:53 PM
|
Replies: 9
Views: 625
Re: 35 3window glass channel question
The rollers on the regulator go in the slides of the lower window channel. The regulator only goes in the door one way. Should answer the question.Usually the regulator rollers face the inner door...
|
Forum: Early V8
02-06-2024, 07:32 PM
|
Replies: 0
Views: 102
|
Forum: Early V8 (1932-53)
02-02-2024, 07:20 PM
|
Replies: 12
Views: 1,026
|
Forum: Early V8 (1932-53)
01-25-2024, 07:46 PM
|
Replies: 9
Views: 836
|
Forum: Early V8 (1932-53)
01-25-2024, 07:45 PM
|
Replies: 14
Views: 792
|
Forum: Early V8
01-24-2024, 09:41 AM
|
Replies: 0
Views: 179
|
Forum: Late V8
01-24-2024, 09:33 AM
|
Replies: 0
Views: 195
|
Forum: Early V8 (1932-53)
01-22-2024, 07:01 PM
|
Replies: 9
Views: 836
Re: 36 five window interior panels
The upholstery panel board are easy to cut with big metal shears. Scissors will kill your hands. Its water resistant. Not water proof. Clean the cut side with a small disc sander they make good door...
|
Forum: Early V8 (1932-53)
01-05-2024, 08:34 PM
|
Replies: 2
Views: 378
|
Forum: Early V8 (1932-53)
12-31-2023, 06:30 PM
|
Replies: 17
Views: 1,245
|
Forum: Early V8 (1932-53)
12-31-2023, 06:27 PM
|
Replies: 3
Views: 423
Re: Sun Visors
Could be a screw at the mount end to tighten. Then it could be sheet metal and you might cruse it a bit more to tighten. On some newer visors they had plastic sleeve. A bit of heat can distort the...
|
Forum: Early V8 (1932-53)
12-26-2023, 03:51 PM
|
Replies: 4
Views: 461
Re: Cowl- Hood Seal
You could secure the rubber with super glue. Then drill and use the screws. I use brush on super glue.
|
Forum: Early V8 (1932-53)
12-17-2023, 11:59 AM
|
Replies: 18
Views: 1,158
|
Forum: Early V8 (1932-53)
12-07-2023, 09:48 AM
|
Replies: 5
Views: 864
Re: Got lucky.
Weldering cable has a good rubber covering. It will take a bunch of abuse
|
Forum: Early V8 (1932-53)
12-06-2023, 01:11 PM
|
Replies: 7
Views: 733
|
Forum: Early V8
11-18-2023, 07:13 PM
|
Replies: 0
Views: 266
32 trunk handle
Looking for a decent trunk lid handle. Key tumbler not important. That’s an easy fix.
Thanks.
Delete
|
Forum: Early V8 (1932-53)
11-16-2023, 08:43 PM
|
Replies: 16
Views: 6,577
|
Forum: Early V8 (1932-53)
09-28-2023, 03:58 PM
|
Replies: 12
Views: 1,034
|
Forum: Early V8 (1932-53)
09-28-2023, 03:49 PM
|
Replies: 5
Views: 779
|