Forum: Model A (1928-31)
06-04-2024, 09:18 AM
|
Replies: 2
Views: 150
Measuring for a horn rod
I have a '30 pickup that did not have a horn rod in it. I've been looking for how to measure it and all I find is measure from point a to point b, but no diagrams to show me what those points are. I...
|
Forum: Model-A
03-01-2024, 11:50 AM
|
Replies: 0
Views: 315
Pickup bed in Kansas or Missouri
Would like to find a pickup bed within 300 miles of KC I can repair or restore for my pickup project. I'm a disabled Vet so money is a considerable factor. Thankyou.
|
Forum: Model A (1928-31)
01-17-2024, 05:49 PM
|
Replies: 13
Views: 784
|
Forum: Model A (1928-31)
01-17-2024, 02:16 PM
|
Replies: 13
Views: 784
Re: #6/9 stamp
Thank you, but I'm a disabled Vet on limited income so these would be out of my budget. Thanks for responding though
|
Forum: Model A (1928-31)
01-17-2024, 12:45 PM
|
Replies: 13
Views: 784
Re: #6/9 stamp
Thanks guys, our club does not have a numbers set. What is a regular vender, Snyders or who? Thanks again,
|
Forum: Model A (1928-31)
01-17-2024, 11:48 AM
|
Replies: 13
Views: 784
|
Forum: Model A (1928-31)
01-17-2024, 11:15 AM
|
Replies: 57
Views: 23,723
Re: Toe-in Adj. tool
I used a 1" round spring loaded curtain/shower rod and it works just great. Kinda like yor flat rod.
|
Forum: Model A (1928-31)
01-17-2024, 11:12 AM
|
Replies: 13
Views: 784
#6/9 stamp
Can anyone tell me where I can buy a correct #6/9? The 9 on my engine is nearly impossible to read and I want to freshen it up. Thanks
|
Forum: Model A (1928-31)
10-02-2023, 07:29 AM
|
Replies: 5
Views: 525
|
Forum: Model A (1928-31)
10-01-2023, 08:53 PM
|
Replies: 5
Views: 525
|
Forum: Model A (1928-31)
10-01-2023, 05:11 PM
|
Replies: 5
Views: 525
Can I move my leatherback front seat back
I recently bought a 1928 Leatherback and it's pretty hard to get in and out of where the front seat is located. I would like to move it back a couple inches but I'm not sure how to go about it. Has...
|
Forum: Model A (1928-31)
04-26-2022, 12:00 PM
|
Replies: 15
Views: 2,081
|
Forum: Model A (1928-31)
04-25-2022, 07:21 PM
|
Replies: 15
Views: 2,081
|
Forum: Model A (1928-31)
04-25-2022, 02:31 PM
|
Replies: 15
Views: 2,081
|
Forum: Model A (1928-31)
04-25-2022, 01:09 PM
|
Replies: 15
Views: 2,081
Re: Gemmer steering box
Thank you. I pulled the grease cap and fitting of today and got a lot of the grease out of the box. Afterwards I put about 1/2 oz. of 600 in it to see if it is going to leak out later today. Thanks...
|
Forum: Model A (1928-31)
04-25-2022, 07:54 AM
|
Replies: 15
Views: 2,081
Re: Gemmer steering box
Thanks, I've ordered some 600w and I'll try to get as much grease out of it as I can and replace it with the 600. Thanks again guys for helping me.
|
Forum: Model A (1928-31)
04-24-2022, 07:20 PM
|
Replies: 15
Views: 2,081
|
Forum: Model A (1928-31)
04-24-2022, 03:01 PM
|
Replies: 15
Views: 2,081
|
Forum: Model A (1928-31)
04-24-2022, 02:15 PM
|
Replies: 15
Views: 2,081
Gemmer steering box
My 1930 Tudor has a Gemmer steering box with the letter F on the engine side. I believe it is a two tooth and would adjust the same as Ford's two tooth. My question is, the box does not have a plug...
|
Forum: Model A (1928-31)
04-14-2022, 09:11 PM
|
Replies: 8
Views: 2,947
|
Forum: Model A (1928-31)
04-14-2022, 06:57 PM
|
Replies: 8
Views: 2,947
|
Forum: Model A (1928-31)
04-14-2022, 04:45 PM
|
Replies: 8
Views: 2,947
|
Forum: Model A (1928-31)
04-14-2022, 01:26 PM
|
Replies: 8
Views: 2,947
Rear main seal replacement
Can anyone tell me how hard it is to replace the rear main seal on my Tudor? I've checked the pan bolts and they are snug so I think it's the upper piece that's leaking.
Thanks
|
Forum: Model-A
03-07-2021, 11:16 AM
|
Replies: 0
Views: 543
Wanted: Weaver auto crane
I'm interested in buying a complete weaver auto crane for my '31 CC. Would prefer one located in the midwest within 400 miles of Kansas City.
|
Forum: Early V8 (1932-53)
09-16-2019, 05:03 PM
|
Replies: 5
Views: 1,092
Re: Looking for 7" tail light trim ring
Thanks Kurt, I have looked at headlight trim rings without any luck. The trim ring for the KD 254 light is a split clamping ring so it can engage in a groove in both the lens and the light body. I...
|