Forum: Model A (1928-31)
12-23-2020, 03:36 PM
|
Replies: 8
Views: 1,624
Re: Brakes
I want to thank everyone for there help with this issue. I will tackle this in the summer next year assuming that I will recover from my present health issues. Jack
|
Forum: Model A (1928-31)
12-21-2020, 11:26 AM
|
Replies: 8
Views: 1,624
Re: Brakes
the PROBLEM THAT i AM HAVING TROUBLE WITH IS THE MECHANICAL CONNECTION BETWEEN THE VACUUM UNIT AND THE MECHANICAL FORD BRAKE RODS. When the brakes are applied the rods are on the pull stroke.. The...
|
Forum: Model A (1928-31)
12-20-2020, 11:33 AM
|
Replies: 8
Views: 1,624
Brakes
While I was laid up these last few months, I was reading about using a vacuum assist on the model A mechanical brakes. Does anyone know anything about this? Jack
|
Forum: Model A (1928-31)
06-28-2020, 08:47 AM
|
Replies: 1
Views: 1,095
Beardsley Crchard Swap meet
I have been hearing contradictory news about a meet there this year. Can anyone give the correct answer. Jack
|
Forum: Model A (1928-31)
06-13-2020, 08:34 AM
|
Replies: 38
Views: 4,315
Re: Temperature Gauge Leak
Unless I am missing something here (and I'm not the sharpest knife in the drawer) it seems that the fancy gooseneck is the issue here. Has anyone tried this gauge in a drilled and tapped standard...
|
Forum: Model A (1928-31)
06-09-2020, 07:43 AM
|
Replies: 3
Views: 973
Re: Carb ID & Help
That is a tillotson x which is a replacement for the factory zenith. They were used a lot in the war trimes into the 50's. Probably some in the 30's as well. Some like them so don't, it is a...
|
Forum: Model A (1928-31)
06-07-2020, 08:35 AM
|
Replies: 15
Views: 2,332
|
Forum: Model A (1928-31)
05-31-2020, 09:07 AM
|
Replies: 26
Views: 5,363
Re: A question about colors
Speaking of paint, where can i get lacquer paint? I know that it is prohibited in many states but if i can get a source i'll work out that problem. Jack
|
Forum: Model A (1928-31)
05-27-2020, 08:24 AM
|
Replies: 18
Views: 4,531
Re: What is this called?
Jack shaft; i have drilled numerous holes and not one came out square. How do you do that? Jack
|
Forum: Model A (1928-31)
05-18-2020, 08:51 AM
|
Replies: 5
Views: 1,471
rear end/ spring
The Les Andrews book page 1 97 paragraph 5a; It says "Attach the right spring shackle first" Does anyone know why?? I think I did this step backward. Any thoughts? Jack
|
Forum: Model A (1928-31)
05-05-2020, 08:01 AM
|
Replies: 20
Views: 3,768
Re: painting a license plate questions
I hope someone can chime in and answer this question. I was told (not by an authority ) that in NY State you cannot paint or restore a plate and have it useful as a YOM for your car. It must be as...
|
Forum: Model A (1928-31)
04-28-2020, 03:31 PM
|
Replies: 1
Views: 1,043
|
Forum: Model A (1928-31)
04-06-2020, 03:11 PM
|
Replies: 111
Views: 14,823
Re: EOG's 1928 Model A Pickup
A really nice truck. The advice given is very good, I would add to change out the carb, the Tilly is not the best for this motor etc. Also look into engine pans and by all means check out the fan...
|
Forum: Model A (1928-31)
03-19-2020, 08:14 AM
|
Replies: 46
Views: 8,323
|
Forum: Model A (1928-31)
03-15-2020, 08:40 AM
|
Replies: 43
Views: 7,307
Re: Flywheel Housing Alignment
I would also like to ask Herm why brass shims, I have steel shims, isn't that OK to use. Also someone mentioned doing this in the car. Is that possible? Jack
|
Forum: Model A (1928-31)
02-22-2020, 04:55 PM
|
Replies: 35
Views: 6,859
Re: Adding Guages
Ruth ' thanks for the reply but the line to the points goes through the ignition switch and it has to be broken and tied directly to the coil which is where I have my problem. This is the same as I...
|
Forum: Model A (1928-31)
02-22-2020, 02:16 PM
|
Replies: 35
Views: 6,859
Re: Adding Guages
Ruth' Can you show how you wired the coil after the ignition switch? I sketched this out and found that I would have to break into the ignition cable that goes to the distributor to do this. Not...
|
Forum: Model A (1928-31)
02-11-2020, 09:09 AM
|
Replies: 5
Views: 1,533
Re: The model a drag link/pitman arm
I also don't fall into the genius category but I am willing to take a guess If the ball were to the outside would the drag link hit the tire on a sharp left turn? Otherwise it must be a geometry...
|
Forum: Model A (1928-31)
01-07-2020, 09:34 AM
|
Replies: 24
Views: 5,330
Re: Engine Stand
I'd be more concerned about the three wheeled engine stand. I had one fall on me and nearly did a lot of damage to my leg. Only 4 wheeled versions now. Jack
|
Forum: Model A (1928-31)
12-14-2019, 10:39 AM
|
Replies: 7
Views: 1,765
|
Forum: Model A (1928-31)
12-11-2019, 09:10 AM
|
Replies: 25
Views: 5,900
Re: Babbit vs Inserts
I don't know the answer to your question, but I have read the same thing. My model A has run for 90 years with the babbit, why change and invite new types of problems? Jack
|
Forum: Model A (1928-31)
12-11-2019, 09:04 AM
|
Replies: 11
Views: 1,921
Re: 30 Tudor Windlace question.
The pictures are great, I think I have it now. If I were smart enough, I would post pictures of the finished product. Thanks again. Jack
|
Forum: Model A (1928-31)
12-10-2019, 06:16 PM
|
Replies: 11
Views: 1,921
|
Forum: Model A (1928-31)
12-10-2019, 06:12 PM
|
Replies: 11
Views: 1,921
|
Forum: Model A (1928-31)
12-10-2019, 01:49 PM
|
Replies: 11
Views: 1,921
|