Forum: Model A (1928-31)
05-27-2024, 11:54 AM
|
Replies: 12
Views: 1,189
|
Forum: Model A (1928-31)
05-22-2024, 05:14 PM
|
Replies: 21
Views: 979
Re: Squeal that I can’t pinpoint
I think I was half asleep in my last post. Distributors do not have bearings, they have bushings. Further, most after market upper distributor shafts have been drilled dead center to the depth of...
|
Forum: Model A (1928-31)
05-22-2024, 03:08 PM
|
Replies: 21
Views: 979
Re: Squeal that I can’t pinpoint
I am not aware of throw out bearings produced in at least the last 20 years that would have the ability to accept grease from the throw out bearing carrier. I think you will probably only grease the...
|
Forum: Model A (1928-31)
03-27-2024, 01:49 PM
|
Replies: 7
Views: 828
Re: Pressure plates
Call Bert's Model A if you are looking for a quality rebuilt pressure plate. He has a rebuilder who does an outstanding job and sets the fingers when rebuilding the pressure plate. So, you just...
|
Forum: Model A (1928-31)
03-22-2024, 12:08 PM
|
Replies: 9
Views: 981
Re: 6V to 12V converter
Thanks to all who responded. I have been running the Laycock for over 10 years. Recently, it started to flutter in and out of overdrive when engaged. I thought perhaps the 12v would keep it...
|
Forum: Model A (1928-31)
03-21-2024, 12:21 PM
|
Replies: 9
Views: 981
6V to 12V converter
I run a 6V positive ground system. I have a Laycock overdrive. It uses a solenoid to engage the unit. I want to install a 6V to 12V converter for the overdrive. I have not found a positive ground...
|
Forum: Model A (1928-31)
02-20-2024, 12:49 PM
|
Replies: 26
Views: 2,136
Re: Backfire
Be sure the nuts in the junction box are tight. A loose of even sung nut can cause your engine to die due to loss of electrical contact.
|
Forum: Model A (1928-31)
02-16-2024, 06:20 PM
|
Replies: 14
Views: 1,249
Re: Distributor Locking Screw, HELP!
Are you referring to the distributor cam lock down screw or the one the goes into the side of the head to lock and ground the distributor?
It sounds like you are referring to the latter. If so,...
|
Forum: Model A (1928-31)
02-12-2024, 06:07 PM
|
Replies: 7
Views: 1,036
Re: New cast iron rear drums
If you want to avoid the issues as stated above, contact Randy Gross at 714-292-8660. I have purchased brake drums and lugs from him several times. Randy sells Model A brake drums and shoes,...
|
Forum: Model A (1928-31)
01-08-2024, 12:58 PM
|
Replies: 4
Views: 745
Re: source for V8 pressure plate?
I have one from Bert's. Give him a call and order one.
I detected no difference of leg pressure required to operate the V8 clutch vs. the stock Model A clutch.
|
Forum: Model A (1928-31)
12-28-2023, 11:51 AM
|
Replies: 10
Views: 1,278
Re: 20-0-20 amp meter
I have a 20-0-20 amp meter and run an alternator. My alternator never charges more than 10-15 amps. So, it has not been a problem for me.
|
Forum: Model A (1928-31)
12-13-2023, 11:46 AM
|
Replies: 34
Views: 2,552
Re: Help “A” guy out.
It could be the square bolt at the top of the springs is not seated in the crossmember slot. To check this, loosen the nuts on the u-bolts holding the spring set. Grab hold of the bumper on the low...
|
Forum: Model A (1928-31)
11-29-2023, 12:26 PM
|
Replies: 32
Views: 2,638
Re: Engine Install
Here is a simple way to line up the splines on the input shaft. I mark the high point of two splines next to each other on the input shaft with a white marker. I also mark a low point on the clutch...
|
Forum: Model A (1928-31)
11-23-2023, 12:28 PM
|
Replies: 20
Views: 2,528
Re: Model A shocks
Shock rebuilder: John Holland 330-483-3896
7208 West Law Rd.
Valley City, OH 44280
(Holland also...
|
Forum: Model A (1928-31)
11-18-2023, 01:24 PM
|
Replies: 16
Views: 1,271
Re: Taillight problem
I mounted a wire in between the mounting bracket and mounting screw. I then ran the wire through the bracket and grounded it to the frame. I have done this with both headlights and tail lights with...
|
Forum: Model A (1928-31)
11-14-2023, 12:53 PM
|
Replies: 21
Views: 2,023
Re: new distributor?
Many Model A folks have asked me "should I stay with a stock dissy or the FS?"
My answer is stay with the stock for one main reason: Should you experience a dissy failure when on a tour, most...
|
Forum: Model A (1928-31)
10-26-2023, 09:49 AM
|
Replies: 14
Views: 1,491
Re: Tires
Hands down it's Goodyear if you are not buying radials. I find Goodyear's tire tread hold the road far better than Firestone's. I have used both them on my A.
|
Forum: Model A (1928-31)
10-11-2023, 11:21 AM
|
Replies: 55
Views: 15,264
Re: Does your Coupe have a Trunk or Rumble seat
31 Coupe. I have a trunk. It sure comes in handy when on an extended tour. I always carry spare parts and tools. I also have plenty of room for luggage and a small cooler when touring. Works...
|
Forum: Model A (1928-31)
10-05-2023, 01:22 PM
|
Replies: 13
Views: 1,192
Re: leaning 30 pickup
One thing to check first. Check to see if the square headed center bolt on the rear springs is seated into the square opening on the crossmember. If it is not seated in the crossmember, loosen the...
|
Forum: Model A (1928-31)
10-05-2023, 01:17 PM
|
Replies: 12
Views: 1,064
Re: Aluminum cam gear install.
The mark on the crank gear is sometimes partially hidden behind the oil slinger. Look closely and you will find it. Line the cam gear marks with the crank gear mark and you are in business.
|
Forum: Model A (1928-31)
09-27-2023, 02:17 PM
|
Replies: 12
Views: 1,286
Re: Overdrive
Before I would convert to 12 volts, I would get a 12 volt battery. Disconnect the power lead to the unit. Ground the positive side of the battery to the overdrive and put power to the unit using the...
|
Forum: Model A (1928-31)
09-26-2023, 11:09 AM
|
Replies: 12
Views: 1,286
Re: Overdrive
I have the Laycock from Rich Little. I am running 6 volts. It has worked fine for 10 years.
First, make sure you have power to the unit.
Second, I run 10-30 wt oil.
When you change the oil, be...
|
Forum: Model A (1928-31)
09-09-2023, 01:19 PM
|
Replies: 7
Views: 632
Re: Speedometer Cable not turning
Sounds like you need a new speedometer drive gear. It is located where the cable goes into the torque tube. You will need to determine what differential gear ratio you have in order to buy the...
|
Forum: Model A (1928-31)
09-01-2023, 10:48 AM
|
Replies: 15
Views: 1,727
Re: Shock Absorber Advice
Here is an excellent shock rebuilder. He is also reasonably priced.
Shock rebuilder: John Holland 330-483-3896
7208 West Law Rd.
...
|
Forum: Model A (1928-31)
08-12-2023, 10:37 AM
|
Replies: 47
Views: 3,666
|