Forum: Early V8 (1932-53)
06-04-2024, 08:31 AM
|
|
Replies: 6
Views: 347
|
|
Forum: Model A (1928-31)
06-04-2024, 07:57 AM
|
|
Replies: 9
Views: 408
|
|
Forum: Early V8 (1932-53)
05-29-2024, 10:23 AM
|
|
Replies: 27
Views: 1,345
|
|
Forum: Early V8 (1932-53)
05-29-2024, 08:08 AM
|
|
Replies: 27
Views: 1,345
|
|
Forum: Early V8 (1932-53)
05-19-2024, 06:51 PM
|
|
Replies: 5
Views: 267
|
|
Forum: Model A (1928-31)
05-15-2024, 07:52 AM
|
|
Replies: 12
Views: 785
|
|
Forum: Early V8 (1932-53)
05-08-2024, 12:23 PM
|
|
Replies: 8
Views: 699
|
|
Forum: Early V8 (1932-53)
05-03-2024, 07:55 AM
|
|
Replies: 21
Views: 879
|
|
Forum: Early V8 (1932-53)
04-28-2024, 11:31 PM
|
|
Replies: 9
Views: 633
|
|
Forum: Early V8 (1932-53)
04-28-2024, 05:44 PM
|
|
Replies: 9
Views: 633
Re: 8BA Bell housing
The starter plate from the Mercury will fit the cast truck housing the difference being the truck is recessed for the dicast seal that bolts on the last two oil pan bolts. If you don't use the seal...
|
|
Forum: Early V8 (1932-53)
04-28-2024, 09:31 AM
|
|
Replies: 9
Views: 753
|
|
Forum: Early V8 (1932-53)
04-24-2024, 05:18 PM
|
|
Replies: 13
Views: 938
Re: Removing perch bolt for repair
If it's still a stock 35 spring it will be attached to the wishbone in front of the axle so it will probably have some tension on it. Use a spring spreader to hold everything in place or porta power...
|
|
Forum: Model A (1928-31)
04-19-2024, 08:15 AM
|
|
Replies: 49
Views: 3,358
|
|
Forum: Early V8 (1932-53)
04-16-2024, 07:28 AM
|
|
Replies: 50
Views: 2,245
|
|
Forum: Early V8 (1932-53)
04-06-2024, 07:59 AM
|
|
Replies: 1
Views: 286
Re: 1950 sedan ignition switch
You have to pull the switch toward you to collapse the spring that seats against the inside of the dash. Rotate until the grooves line up and release.
|
|
Forum: Early V8 (1932-53)
04-01-2024, 07:16 PM
|
|
Replies: 23
Views: 1,477
Re: Clutch Release Shaft Bushing tool
Try the hose clamp around the bushing. It works just like the piston ring compressor as you drive the bushing in. I ruined two before I tried the clamp.
|
|
Forum: Early V8 (1932-53)
03-26-2024, 11:48 AM
|
|
Replies: 23
Views: 1,477
|
|
Forum: Model A (1928-31)
03-25-2024, 07:58 AM
|
|
Replies: 15
Views: 1,407
|
|
Forum: Early V8 (1932-53)
03-20-2024, 07:48 AM
|
|
Replies: 21
Views: 1,340
|
|
Forum: Early V8 (1932-53)
03-19-2024, 01:19 PM
|
|
Replies: 23
Views: 1,708
|
|
Forum: Early V8 (1932-53)
03-17-2024, 08:52 AM
|
|
Replies: 19
Views: 1,049
|
|
Forum: Early V8 (1932-53)
03-12-2024, 08:07 AM
|
|
Replies: 25
Views: 1,246
|
|
Forum: Early V8 (1932-53)
03-12-2024, 08:02 AM
|
|
Replies: 2
Views: 406
|
|
Forum: Early V8 (1932-53)
02-27-2024, 08:49 PM
|
|
Replies: 17
Views: 1,008
|
|
Forum: Early V8 (1932-53)
02-27-2024, 06:28 PM
|
|
Replies: 17
Views: 1,008
Re: Wheels Rotating in Opposite Direction
I meant to see if the truck would roll to eliminate the rearend as the problem. but in looking at the shifter tower the slots are not lined up for the shifter handle side to side as in neutral. The...
|
